Cabinet rule 5181
Cabinet rule 5181 - Image 2

SKU: 5181010001

Cabinet rule 5181

EUR11.44

Available in central stock
Quick facts

Additional Information

Weight0.1 kg
Material

Stainless steel, Steel end plates

Surface treatment

Polished stainless steel, End plate untreated

Model: Albert Karlsson Metallfabriksbolag “Ticka Standard”

Period: 1930-1960

An end cap is included.

This model is intended for overlapping doors.

It is placed vertically at the top edge of the door on lower cabinets (as shown), vertically but upside down compared to the picture at the bottom edge of upper cabinets, and horizontally on the side of the door on upper cabinets.

When installing cabinet frames on lacquered cabinet doors, the screws should not be overtightened to avoid cracking the lacquer.

Use a screwdriver instead of a screwdriver.

Screw not included.

Matching screw number 9 for the bolt and screw number 19 for the end plate

Description

Model: Albert Karlsson Metallfabriksbolag “Ticka Standard”

Period: 1930-1960

An end cap is included.

This model is intended for overlapping doors.

It is placed vertically at the top edge of the door on lower cabinets (as shown), vertically but upside down compared to the picture at the bottom edge of upper cabinets, and horizontally on the side of the door on upper cabinets.

When installing cabinet frames on lacquered cabinet doors, the screws should not be overtightened to avoid cracking the lacquer.

Use a screwdriver instead of a screwdriver.

Screw not included.

Matching screw number 9 for the bolt and screw number 19 for the end plate

Additional Information

Weight0.1 kg
Material

Stainless steel, Steel end plates

Surface treatment

Polished stainless steel, End plate untreated

Reviews

There are no reviews yet

Be the first to review “Cabinet rule 5181”

Your email address will not be published. Required fields are marked *

You may also need to

Screw 9 nickel-plated TKFS 3X16 per piece

EUR0.37

Add to Cart

Screw 19 galvanized TFS 3.5×19 mm per piece

EUR0.37

Add to Cart

Screw 19 zinc plated TFS 3,5×19 mm 10 pack

EUR3.20

Add to Cart

Screw 9 nickel plated TKFS 3X16 10 pack

EUR3.20

Add to Cart

Related products

Cabinet rule 5181U

Model: Albert Karlsson Metallfabriksbolag “Ticka Standard”

Period: 1930-1960

Without striker plate. Used as a handle on cabinet doors with other closing mechanisms, such as magnetic locks or self-closing hinges. The cabinet handle does not have a latch and therefore does not require drilling in the door.

For placement, see article number 5181.

When installing cabinet frames on lacquered cabinet doors, the screws should not be overtightened to avoid cracking the lacquer.

Use screwdrivers, not screwdrivers.

Screw not included.

Matching screw number 19

EUR8.69

Double hook

Classic double hook from the period 1920 to 1965. The hook is available in untreated brass or nickel-plated brass. Screws are included.

Price range: EUR9.15 through EUR10.07

Knob board with 4 turned knobs

Coat rack in pine after a model from around 1870. Turned knobs. The board is edged all around with carnis profile. Sturdy and useful for clothes, work clothes, in kitchens for towels and aprons, etc. Was usually painted in the same color as the other carpentry in the room. Two lengths, one with four knobs and one with six.

EUR56.27

Kitchen stove rod nickel-plated 105 cm complete

Rod to attach above the kitchen stove for kitchen utensils, potholders etc. Can also be used as a towel rack in the kitchen, or in the bathroom.

MATERIAL Made of solid nickel-plated brass. Polished shiny surface, but not lacquered. The model was common from the late 1800s until the 1930s. Highest quality.

MOUNTING The wall brackets have sturdy iron screws (3.5 mm) that are screwed (carefully!) into the wall. The hooks and brackets are then screwed onto the pole. Last of all, you tighten the screws that prevent the bar from rolling.

TIP The bar can be shortened by sawing it off. It can also be connected to another pole if you want a longer version. In that case, you should place another wall bracket over the joint and buy an extra coupling bracket.

EUR382.01

Plate shelf

Shelf for placing dishes and plates after a model from the 18th century from Ovansjö parish in Gästrikland. Four shelves, three of which are intended for plates. The original shelf is painted in English red with green front edges on shelves and support strips. Well made carpentry work. Unpainted.

EUR429.59

Kitchen stove rod brass 1.5 m complete

Rod to attach above the kitchen stove for kitchen utensils, potholders etc. Can also be used as a towel rack in bathrooms. The model was common from the late 1800s until the 1930s.

MATERIAL Made of solid brass or in nickel-plated version. Polished shiny surface, but not lacquered. The brass darkens over time if you do not polish it.

MOUNTING The wall brackets have sturdy iron screws (3.5 mm) that are screwed (carefully!) into the wall. The hooks and brackets are then screwed onto the pole. Last of all, you tighten the screws that prevent the bar from rolling.

TIP! The bar can be shortened by sawing it off. It can also be connected to another pole if you want a longer version. In this case, a wall bracket should be placed over the joint.

EUR447.44

Related articles

There are no related articles for this product.

Cabinet rule 5181

Model: Albert Karlsson Metallfabriksbolag "Ticka Standard"

Period: 1930-1960

An end cap is included.

This model is intended for overlapping doors.

It is placed vertically at the top edge of the door on lower cabinets (as shown), vertically but upside down compared to the picture at the bottom edge of upper cabinets, and horizontally on the side of the door on upper cabinets.

When installing cabinet frames on lacquered cabinet doors, the screws should not be overtightened to avoid cracking the lacquer.

Use a screwdriver instead of a screwdriver.

Screw not included.

Matching screw number 9 for the bolt and screw number 19 for the end plate

Please leave a comment what you think about our new webshop

This site is registered on wpml.org as a development site. Switch to a production site key to remove this banner.