SKU: 5181010001

Cabinet rule 5181

EUR11.44

Available in central stock
Quick facts

Additional Information

Weight0.1 kg
Material

Stainless steel, Steel end plates

Surface treatment

Polished stainless steel, End plate untreated

Model: Albert Karlsson Metallfabriksbolag “Ticka Standard”

Period: 1930-1960

An end cap is included.

This model is intended for overlapping doors.

It is placed vertically at the top edge of the door on lower cabinets (as shown), vertically but upside down compared to the picture at the bottom edge of upper cabinets, and horizontally on the side of the door on upper cabinets.

When installing cabinet frames on lacquered cabinet doors, the screws should not be overtightened to avoid cracking the lacquer.

Use a screwdriver instead of a screwdriver.

Screw not included.

Matching screw number 9 for the bolt and screw number 19 for the end plate

Description

Model: Albert Karlsson Metallfabriksbolag “Ticka Standard”

Period: 1930-1960

An end cap is included.

This model is intended for overlapping doors.

It is placed vertically at the top edge of the door on lower cabinets (as shown), vertically but upside down compared to the picture at the bottom edge of upper cabinets, and horizontally on the side of the door on upper cabinets.

When installing cabinet frames on lacquered cabinet doors, the screws should not be overtightened to avoid cracking the lacquer.

Use a screwdriver instead of a screwdriver.

Screw not included.

Matching screw number 9 for the bolt and screw number 19 for the end plate

Additional Information

Weight0.1 kg
Material

Stainless steel, Steel end plates

Surface treatment

Polished stainless steel, End plate untreated

Reviews

There are no reviews yet

Be the first to review “Cabinet rule 5181”

Your email address will not be published. Required fields are marked *

Related products

Single hook

Single hook in nickel-plated or untreated brass. Common during the period 1920 – 1965. Screw included.

Price range: EUR5.03 through EUR5.49

Nail brush

Nail brush in oiled oak and white fiber. Double-sided nail brush that is both stylish and comfortable to hold.White fiber is elastic and water resistant with a certain stiffness but without becoming too hard, which makes the material comfortable and practical when cleaning hands and nails. The shorter stiffer bristles on the top of the brush effectively access and remove dirt under the nail.

Weight 38 g. Length 10 cm. Width 4 cm. Height 3cm

EUR16.47

Knob board with 4 turned knobs

Coat rack in pine after a model from around 1870. Turned knobs. The board is edged all around with carnis profile. Sturdy and useful for clothes, work clothes, in kitchens for towels and aprons, etc. Was usually painted in the same color as the other carpentry in the room. Two lengths, one with four knobs and one with six.

EUR56.27

Kitchen shelf / pantry shelf shelf

Loose shelf in untreated pine with profiled edge at the bottom for our console ladder for kitchen shelf / pantry shelf or loose consoles. Based on a model from around 1905.

Shelf. Length 125 cm depth 28 cm. Thickness 2 cm. Unpainted.

Note! Brackets pictured are not included but can be purchased separately.

EUR72.74

Loose bracket ladder

Loose bracket ladder for our pantry shelf. The price is for one bracket ladder.

Please note that the three shelves are not included but purchased separately and that the price is for a ladder. See related products.

EUR141.37

Kitchen stove rod brass 80 cm complete

Rod to attach above the kitchen stove for kitchen utensils, potholders etc. Can also be used as a towel rack in the kitchen, or in the bathroom. The model was common from the late 19th century until the 1930s.

MATERIAL Highest quality. Sand-cast brass. Polished shiny surface, but not lacquered. The brass darkens over time if not polished.

Length with knobs 80 cm

MOUNTING The wall brackets have sturdy iron screws (3.5 mm) that are carefully screwed into the wall. The hooks and brackets are then screwed onto the bar. Last of all, tighten the screws that prevent the bar from rolling.

TIP The bar can be shortened by sawing it off. It can also be connected to another pole if you want a longer version. In this case, you should use a so-called coupling sleeve and place a wall bracket over the joint.

Also available in nickel-plated version.

EUR300.58

Related articles

There are no related articles for this product.

Cabinet rule 5181

Model: Albert Karlsson Metallfabriksbolag "Ticka Standard"

Period: 1930-1960

An end cap is included.

This model is intended for overlapping doors.

It is placed vertically at the top edge of the door on lower cabinets (as shown), vertically but upside down compared to the picture at the bottom edge of upper cabinets, and horizontally on the side of the door on upper cabinets.

When installing cabinet frames on lacquered cabinet doors, the screws should not be overtightened to avoid cracking the lacquer.

Use a screwdriver instead of a screwdriver.

Screw not included.

Matching screw number 9 for the bolt and screw number 19 for the end plate

Please leave a comment what you think about our new webshop

This site is registered on wpml.org as a development site. Switch to a production site key to remove this banner.